# Getting water to temp **URL:** \ **Category:** Anova Precision® Cooker\ **Created:** [January 3, 2016, 11:54pm UTC](https://community.anovaculinary.com/t/getting-water-to-temp/687 "2016-01-03T23:54:50Z")\ **Posts on this page:** 9\ **Page:** 1
**Author:** ![enichols](https://avatars.discourse-cdn.com/v4/letter/e/0ea827/32.png) [@enichols](https://community.anovaculinary.com/u/enichols)\ **Post date:** [January 3, 2016, 11:54pm UTC](https://community.anovaculinary.com/t/getting-water-to-temp/687/1 "2016-01-03T23:54:50Z")
Hi, it has taken almost an hour to get room temp water up to temperature of 183 f.  Is that normal? ---
**Author:** ![fischersd](https://sea2.discourse-cdn.com/flex016/user_avatar/community.anovaculinary.com/fischersd/32/5594_2.png) [@fischersd](https://community.anovaculinary.com/u/fischersd)\ **Post date:** [January 4, 2016, 12:02pm UTC](https://community.anovaculinary.com/t/getting-water-to-temp/687/2 "2016-01-04T12:02:41Z")
It could be.  There are factors here that you haven’t stated.  What’s the temperature of the room?  What container are you using (and what volume?) - non-insulative containers will take longer as they’ll lose heat to the room.   Not having the container at least partially covered will also prolong the heating process.   Me, I try to shorten the process by using hot water from the tap, to give the PC a head start - I also use a Cambro 4.5 gallon polycarbonate container and have the cover on while bringing it up to temperature to shorten the time as much as possible.  Others have had a lot of success by customizing plastic coolers, which are insulated, to minimize heat loss. ---
**Author:** ![AngelArs](https://avatars.discourse-cdn.com/v4/letter/a/b9e5f3/32.png) [@AngelArs](https://community.anovaculinary.com/u/AngelArs)\ **Post date:** [January 4, 2016, 9:14pm UTC](https://community.anovaculinary.com/t/getting-water-to-temp/687/3 "2016-01-04T21:14:46Z")
\> @enichols said: > Hi, it has taken almost an hour to get room temp water up to temperature of 183 f.  Is that normal? > > > > Lower wattage units (_800 watts_) will take up to 30% longer to heat up the water than higher wattage units (_1100 watts_). As suggested you can use hot water to help it a bit, just don’t go over the target water temp (_183F_). ---
**Author:** ![john.jcb](https://sea2.discourse-cdn.com/flex016/user_avatar/community.anovaculinary.com/john.jcb/32/7269_2.png) [@john.jcb](https://community.anovaculinary.com/u/john.jcb)\ **Post date:** [January 5, 2016, 4:43pm UTC](https://community.anovaculinary.com/t/getting-water-to-temp/687/4 "2016-01-05T16:43:27Z")
Using a properly sized vessel will significantly shorten the heat up time as well. WHen cooking for myself I often use a soup pot which heats hot tap water pretty quickly. ---
**Author:** ![jordan](https://sea2.discourse-cdn.com/flex016/user_avatar/community.anovaculinary.com/jordan/32/532_2.png) [@jordan](https://community.anovaculinary.com/u/jordan)\ **Post date:** [January 20, 2016, 10:34pm UTC](https://community.anovaculinary.com/t/getting-water-to-temp/687/5 "2016-01-20T22:34:54Z")
@fischersd I do the hot tap water, too. Works like a charm. My own personal trick for when I’m really impatient (i.e., weeknights when I don’t have food cooking during the day with WI-FI), is to put the pot on the stove for a few minutes while I’m prepping the food. I don’t recommend doing this while the device is attached to the pot and running (but in full disclosure, the answer is yes, I have done it once or twice…shame on me.) Anywho, the trick is to remove the pot from the stove at the first sign of tiny bubbles (right before the water starts to “quiver”). At that point, temp is a little under 140F, so for most things I cook when on weeknights when I’m in impatient mode (read, hangry), it’s perfect. I simply pop the PC onto the pot and let it do the rest. I don’t mind overshooting by three or four degrees when I’m giving the water my hangry pre-heat on the stove, because the temp drops a few degrees when I drop the meat in anyways. ---
**Author:** ![john.jcb](https://sea2.discourse-cdn.com/flex016/user_avatar/community.anovaculinary.com/john.jcb/32/7269_2.png) [@john.jcb](https://community.anovaculinary.com/u/john.jcb)\ **Post date:** [January 20, 2016, 11:09pm UTC](https://community.anovaculinary.com/t/getting-water-to-temp/687/6 "2016-01-20T23:09:52Z")
For things like a steak I also dont think it hurts to put it in early. That way as the water reaches temperature the meat is not far behind. Thicker steaks and roasts will of course take a little longer to stabilize. ---
**Author:** ![Heather](https://avatars.discourse-cdn.com/v4/letter/h/9f8e36/32.png) [@Heather](https://community.anovaculinary.com/u/Heather)\ **Post date:** [February 29, 2016, 8:52pm UTC](https://community.anovaculinary.com/t/getting-water-to-temp/687/7 "2016-02-29T20:52:30Z")
How much water, how fast, what was the starting temperature of the water, and was this sterile water? All these are factors that could have contributed. ---
**Author:** ![Heather](https://avatars.discourse-cdn.com/v4/letter/h/9f8e36/32.png) [@Heather](https://community.anovaculinary.com/u/Heather)\ **Post date:** [February 29, 2016, 8:52pm UTC](https://community.anovaculinary.com/t/getting-water-to-temp/687/8 "2016-02-29T20:52:50Z")
How much water, how fast, what was the starting temperature of the water, and was this sterile water? All these are factors that could have contributed. ---
**Author:** ![Jakerobinson](https://sea2.discourse-cdn.com/flex016/user_avatar/community.anovaculinary.com/jakerobinson/32/1466_2.png) [@Jakerobinson](https://community.anovaculinary.com/u/Jakerobinson)\ **Post date:** [January 1, 2017, 9:27am UTC](https://community.anovaculinary.com/t/getting-water-to-temp/687/9 "2017-01-01T09:27:59Z")
I’m new to sv but I do two things to bring temp up quickly 1. I’ve got two tea kettles and I have both of them heating a full pot 2. hottest tap water poured in to bring water level up. My Tap water is not really hot, so once kettles are done the tap water + boiling kettles brings temp to right at 128° in a styrofoam cooler. Because the unit sits high in the cooker it takes about 4 pictures of tap water + 2 kettles to get to proper water level and 128°. From there it only takes a few minutes to get to 134° (my last recipe target temp) I am betting you could experiment with kettle water + tap and create a cheat sheet to help get to different Temps desired based on cooking containers ![](https://us1.discourse-cdn.com/flex016/uploads/anova/original/1X/3f1a6a5f70059b501082fb5e240bcf94679535f7.jpg)